Welcome to the official website of Nanyang Huaye Explosion-proof Instrument Co., Ltd!
Service Hotline:0377-61613169 | E-mail: abc@huayex.com
BHD2-10/127-4T Mining flameproof low voltage cable junction box
Optional parameters Single junction box (without temperature sensor) With temperature sensor junction box (platinum thermal resistor Pt100) With 4-20mA temperature transmitter junction box
Classification:
Detailed introduction
1. Overview
BHD2-10/127-3T explosion-proof low-voltage cable junction box for mining is designed and produced according to the provisions of GB/T3836.1 "Explosive gas environment Part 1: General requirements for equipment", GB/T3836.2 "Explosive environment Part 2: Equipment protected by explosion-proof enclosure "d", MT429-2008 "Explosion-proof low-voltage cable junction box for coal mines", and MT381-1995 "General technical conditions for temperature sensors for mining". It is manufactured into a explosion-proof product for mining, specially used for temperature measurement in explosive mixtures (methane) and underground coal mines.
The shell is made of cast steel (or cast iron), and the surface is sprayed with anti-corrosion paint.
The explosion-proof mark is ExdbIMb
2. Explosion-proof principle
BHD2-10/127-3T mining flameproof low-voltage cable junction box adopts explosion-proof shell, which separates the circuit part that may generate sparks and arcs from the explosive gas mixture outside the shell, so as to achieve the purpose of flameproof. The size of the flameproof joint surface complies with the provisions of GB/T3836.2, and the cable entry device complies with the provisions of Appendix D of GB3836.1-2000.
3. Model meaning
BHD2-10/127-4T mining flameproof low-voltage cable junction box is mainly used as a matching junction box for temperature transmitters in coal mine environments. It contains five-way temperature transmitters with double input and double output.
4. Technical indicators
1. Ambient temperature: -20℃～40℃;
2. Relative humidity: ≤98% (+25℃);
3. No corrosive gas that damages insulation in coal mines;
4. Operating voltage: ≤127V;
5. Atmospheric pressure: 80KPa～106KPa.
Sealing ring size:
5. Selection Instructions
When selecting a model, users should specify:
1. Model;
2. Whether it is equipped with a sensor or a transmitter. If equipped with a sensor, the diameter and length of the sensor protection tube, as well as the lead length and installation thread should be indicated.
6. Installation and wiring
1. During installation, check whether the explosion-proof mark on the brand name is consistent with the installation environment;
2. The connecting wire should be a copper shielded cable with a cross-section of not less than 0.2 square millimeters;
3. Open the junction box, use a wrench to unscrew the compression nut of the cable entry device, firmly connect the cable to the wiring bolt (or terminal) in the junction box, then cover the junction box cover and tighten the fastening screws at the four corners;
4. The grounding screw on the junction box must be reliably grounded with a grounding wire;
5. During installation, the signal transmission line should be fixed with a tie at a distance of no more than 300mm. When the signal transmission line is too long, it can be tied in a suitable position. Do not throw it around and keep it away from heating equipment;
6. When the sealing ring in the introduction device ages and hardens, it should be replaced in time;
7. During maintenance, attention should be paid to preventing "explosion failure" (such as protecting the explosion-proof surface, paying attention to tightening and the rubber sealing ring in the introduction device);
8. The minimum outer diameter of the cable used by the user is ￠6;
9. If the "immovable" thread installation method is selected, the probe part should be installed first, and then the junction box.
Key words:
BHD2-10/127-4T Mining flameproof low voltage cable junction box
* Note: Please be sure to fill in the information accurately and keep the communication unblocked. We will get in touch with you as soon as possible.
Nanyang Huaye Explosion Protected Instrument Co., Ltd.
Professional manufacturer of explosion-proof temperature meters and temperature sensors and suppliers of motor supporting instruments
Professional manufacturer of explosion-proof temperature instruments and temperature sensors, as well...
24-hour service hotline
Mobile:+86-15093007079 / +86-13838705322
Address: Middle Section of 3# Road, 2# Industrial Park, High-tech Zone, Nanyang City, Henan Province
E-mail:abc@huayex.com
Fax:+86-377-61613132
Copyright©Nanyang Huaye Explosion Protected Instrument Co., Ltd. This site already supports IPV6 Business License